Calf Buddy™ 1 - 9L
Product No. 900050
A high-quality, semi-transparent hutch bucket comes with the Calf Buddy™ Teat and Connector to control the milk flow for optimum health.The Calf Buddy™ 1 not only looks beautiful but is also highly functional! The 9L capacity and semi transparent wall is perfect to monitor volume. It comes with a sturdy stainless handle and can be hung from the base after use. Fitted with the Calf Buddy™ Teat and Connector - the milk flow is controlled, calves are heavier, healthier and cost less to rear.
A high-quality, semi-transparent hutch bucket comes with the Calf Buddy™ Teat and Connector to control the milk flow for optimum health.
The Calf Buddy™ 1 not only looks beautiful but is also highly functional! The 9L capacity and semi transparent wall is perfect to monitor volume. It comes with a sturdy stainless handle and can be hung from the base after use. Fitted with the Calf Buddy™ Teat and Connector - the milk flow is controlled, calves are heavier, healthier and cost less to rear.
The bucket hangs on any standard hutch bucket bracket and has a slot at the base to hang it upside down after feeding.
The Calf Buddy™ 1 comes with a Calf Buddy™ Teat and Connector. Calf Buddy™ Teats have a pull through design to sit snugly against the feeder wall for optimum hygiene. This is the most hygienic connection system, and with the 1 Click connection, it is also easy to change.
When to Replace
Calf Buddy™ Teats control the flow for around 120 feeds. Best practice is to use the One Teat - One Calf rule. New calf = new teat. When the calf is weaned, remove the worn teat and replace with new for the next calf.
If you are using one bucket for multiple calves then managing the teats as you would your milking liners helps maintain a consistent, controlled flow and takes away guess work.
A simple calculation will tell you when to replace the teats: 120 ÷ feeds per day ÷ 7 = weeks until replacement.
For example, if the teat is used twice a day, replace it every 8.5 weeks: 120 ÷ 2 ÷ 7 = 8.5 weeks.
If the teat is used four times a day, replace it every 4.2 weeks: 120 ÷ 4 ÷ 7 = 4.2 weeks.
How to change
Calf Buddy™ Teats have a pull through design to sit snugly against the feeder wall for optimum hygiene. This is the most hygienic connection system in hutch buckets, and with the 1 Click connection, it is also easy to change!
Connect the teat to the Calf Buddy™ Connector, making sure the teat and connectors line up.
Pull the teat through the hutch bucket.
Using an up and down motion, pull the teat through the bucket until you hear the 'click'.
Finally, be sure to check the teat alignment is correct and the slit is vertical!
Removing a worn teat
Place your hand inside the bucket and pull the connector upwards until it disconnects from the teat.
Remove the worn teat and discard it.
Wash the connector and insert it into a new Calf Buddy™ Teat. So easy!
Milk contains both fat and protein, which can form biofilm. This biofilm can give bacteria a perfect enviroment to multiply, even when a surface looks clean. Effective cleaning must remove both fat and protein.
Rinse equipment soon after feeding so milk does not dry onto the surface.
Use warm water and a suitable detergent rather than very hot water. Hot water can set or bake milk protein onto the equipment.
Calf Buddy™ Teats are made from high-quality natural rubber, so they should be cleaned with a non-chlorine detergent. Chlorine-based detergents damage natural rubber, reducing teat life and performance.
Clean thoroughly at least twice a week, and rinse after every feed. Regular cleaning removes milk fat and protein before they form biofilms that allow bacteria to grow, helping maintain excellent hygiene for every feed.
Rinse with water.
Apply a gentle, non-chlorine detergent as directed.
Lightly brush the outside while bending each teat so detergent reaches the inner wall.
Rinse thoroughly.
Calf Buddy™ Teats do not need to be removed for cleaning!
Comes with a Calf Buddy™ Teat and Connector.
Volume: 9L
Weight: 700gm
Length: 290mm
Height: 400mm
Width: 270mm
Optional Lid - Code 900051
Optional Bracket - Code 900008
Warranty
One-year warranty with proof of purchase, excluding consumable items such as teats.
NZ Pat Apps 757655, 767633, 727000, 787005.
NZ Des Reg. 420972 PCT Patent Applications
NZ2016/050190 & NZ2020/050110 International
Patents and Designs pending or apply.