Milk Bar
900000.jpg
900000-calf-buddy-teat-reduce-cross-suckling.png
900002-calf-buddy-starter-hutch-bucket.png
900000-calf-buddy-teat-saliva-health.png
900000-calf-buddy-teat-saliva.png
900001-calf-buddy-connector-connected.png
900001-calf-buddy-connector.png
900002-calf-buddy-starter-1.png
900002-calf-buddy-starter-2.png
900002-calf-buddy-starter-3.png

Calf Buddy™ Teat

Product No. 900000

The Calf Buddy™ Teat by Milk Bar™ fits any typical hutch bucket. The ultra-hygienic connection system has no screw in valves and is easy to fit.The Calf Buddy™ Teat controls the milk flow in typical hutch buckets to improve calf health. The teat activates saliva production in improve calf digestion and increase average daily gains. Cross suckling/ hyper-active behaviour post feeding is reduced which opens oppurtunities to pair calves to reduce time.

The Calf Buddy™ Teat by Milk Bar™ fits any typical hutch bucket. The ultra-hygienic connection system has no screw in valves and is easy to fit.

The Calf Buddy™ Teat controls the milk flow in typical hutch buckets to improve calf health. The teat activates saliva production in improve calf digestion and increase average daily gains.

Cross suckling/ hyper-active behaviour post feeding is reduced which opens oppurtunities to pair calves to reduce time.

By following the simple rule of One Teat - One Calf the whole calf operation runs more effeciently with reductions in time and labour. After training, fit a new Calf Buddy™ Teat into the calfs hutch bucket. This bucket stays with this calf until weaning.

When to Replace

Calf Buddy™ Teats control the flow for around 120 feeds. Best practice is to use the One Teat - One Calf rule. New calf = new teat. When the calf is weaned, remove the worn teat and replace with new for the next calf.

If you are using one bucket for multiple calves then managing the teats as you would your milking liners helps maintain a consistent, controlled flow and takes away guess work.

A simple calculation will tell you when to replace the teats: 120 ÷ feeds per day ÷ 7 = weeks until replacement.

For example, if the teat is used twice a day, replace it every 8.5 weeks: 120 ÷ 2 ÷ 7 = 8.5 weeks.

If the teat is used four times a day, replace it every 4.2 weeks: 120 ÷ 4 ÷ 7 = 4.2 weeks.

How to change

Calf Buddy™ Teats have a pull through design to sit snugly against the feeder wall for optimum hygiene. This is the most hygienic connection system in hutch buckets, and with the 1 Click connection, it is also easy to change!

  1. Connect the teat to the Calf Buddy™ Connector, making sure the teat and connectors line up.

  2. Pull the teat through the hutch bucket.

  3. Using an up and down motion, pull the teat through the bucket until you hear the 'click'.

Finally, be sure to check the teat alignment is correct and the slit is vertical!

Removing a worn teat

  1. Place your hand inside the bucket and pull the connector upwards until it disconnects from the teat.

  2. Remove the worn teat and discard it.

  3. Wash the connector and insert it into a new Calf Buddy™ Teat. So easy!

Milk contains both fat and protein, which can form biofilm. This biofilm can give bacteria a perfect enviroment to multiply, even when a surface looks clean. Effective cleaning must remove both fat and protein.

Rinse equipment soon after feeding so milk does not dry onto the surface.

Use warm water and a suitable detergent rather than very hot water. Hot water can set or bake milk protein onto the equipment.

Calf Buddy™ Teats are made from high-quality natural rubber, so they should be cleaned with a non-chlorine detergent. Chlorine-based detergents damage natural rubber, reducing teat life and performance.

Clean thoroughly at least twice a week, and rinse after every feed. Regular cleaning removes milk fat and protein before they form biofilms that allow bacteria to grow, helping maintain excellent hygiene for every feed.

  1. Rinse with water.

  2. Apply a gentle, non-chlorine detergent as directed.

  3. Lightly brush the outside while bending each teat so detergent reaches the inner wall.

  4. Rinse thoroughly.

Calf Buddy™ Teats do not need to be removed for cleaning!

Pack Size: 10

Calf Buddy™ Teats come in recyclable packaging.

Calf Buddy™ Teats are made from a the highest grade natural rubber.

Milk Bar™ Teats are protected by patents and registered designs, reflecting decades of innovation dedicated to improving calf health and feeding performance.

NZ Pat Appln 787055 PCT Patent Application PCT/NZ2020/050110 EU Design 001449680-0001 International designs apply. International Patents pending or apply.

Lorem ipsum dolor sit amet consectetur

Related products