Milk Bar
912500.jpg
912500-milk-bar-15-compartment-close.png
912500-milk-bar-15-compartment.png

Milk Bar™ 15 Compartment

Product No. 912500

The Milk Bar™ 15 Compartment is a specialised unit to fill the needs of a few select farms.Seven brace handles and aluminium hooks keep this long feeder straight and secure on the gates.Using the Milk Bar™ Teat is what makes feeding a large group of calves with a compartment feeder possible. The Milk Bar™ Teat controls and regulates the milk flow and delivers a much more even feed.This feeder is only available in New Zealand - contact us to see if the Milk Bar™ 15 Compartment is right for your farm.

The Milk Bar™ 15 Compartment is a specialised unit to fill the needs of a few select farms.

Seven brace handles and aluminium hooks keep this long feeder straight and secure on the gates.

Using the Milk Bar™ Teat is what makes feeding a large group of calves with a compartment feeder possible. The Milk Bar™ Teat controls and regulates the milk flow and delivers a much more even feed.

This feeder is only available in New Zealand - contact us to see if the Milk Bar™ 15 Compartment is right for your farm.

Using a screwdriver, adjust the aluminium hooks to fit your gate.

Fill with milk and leave the calves to it.

To give your calves the best drinking position, hang the feeder on a rail around 110cm high. This puts the teat at 60cm which is the optimum height for calves and helps the oesophageal groove to close and milk to bypass the rumen.

When to Replace

Milk Bar™ Teats control the flow for around 120 feeds. This figure is influenced by cleaning regimes, as the natural rubber gradually absorbs milk fat and protein. With use, the teat softens and the flow increases - calf behaviour will indicate when the teats have become soft and need replacement! As the milk flow increases they will start to suck on each other or their surroundings (cross-suckling). As soon as you start to see cross-suckling, change your teats to prevent the next stage of fast flow - diarrhoea.

However - managing the teats as you would your milking liners helps maintain a consistent, controlled flow and takes away guess work.

A simple calculation will tell you when to replace the teats: 120 ÷ feeds per day ÷ 7 = weeks until replacement.

For example, if the teat is used twice a day, replace it every 8.5 weeks: 120 ÷ 2 ÷ 7 = 8.5 weeks.

If the teat is used four times a day, replace it every 4.2 weeks: 120 ÷ 4 ÷ 7 = 4.2 weeks.

Replace immediately if calves start gulping or cross-suckling.Good teat management helps maintain good calf digestive health.

How to Change

Milk Bar™ Teats use a hygienic pull-through design that fits tightly against the feeder wall to minimise milk build-up.

Correct installation is important: position the slit vertically for optimum performance.

  1. Teat Tool: The quickest and easiest removal method.

  2. By hand: Pull the teat straight up or down—not directly outward.

  3. Cutting: Use a sharp blade away from your body.

Check the new teat is inserted with the slit vertical.

Milk contains both fat and protein, which can form biofilm. This biofilm can give bacteria a perfect enviroment to multiply, even when a surface looks clean. Effective cleaning must remove both fat and protein.

Rinse equipment soon after feeding so milk does not dry onto the surface.

Use warm water and a suitable detergent rather than very hot water. Hot water can set or bake milk protein onto the equipment.

Milk Bar™ Teats are made from high-quality natural rubber, so they should be cleaned with a non-chlorine detergent. Chlorine-based detergents damage natural rubber, reducing teat life and performance.

Clean thoroughly at least twice a week, and rinse after every feed. Regular cleaning removes milk fat and protein before they form biofilms that allow bacteria to grow, helping maintain excellent hygiene for every feed.

  1. Rinse with water.

  2. Apply a gentle, non-chlorine detergent as directed.

  3. Lightly brush the outside while bending each teat so detergent reaches the inner wall.

  4. Rinse thoroughly.

The Milk Bar™ 15 Compartment comes ready to use with Milk Bar™ Teats and hooks fitted.

Volume: 2.5L ea

Weight: 16kg

Length: 3.3m

Height: 350mm

Width: 210mm

Warranty

The feeder has a two year warranty with proof of purchase.

The warranty does not apply to consumable parts (teats and hooks).

Made from food grade polyethylene and U.V Stabilised for long life.

Lorem ipsum dolor sit amet consectetur

Related products