Milk Bar

Milk Bar™ 20

Product No. 910800

The solid base keeps the Milk Bar™ stable while 20 calves easily find a teat on the round design. The Milk Bar™ 20 design makes it very sturdy for calves of all ages.The feeder bowl stacks inside the base when not in use to reduce storage space.There are loads of creative ways to fill the Milk Bar™ 20, but typically a hose is the easiest to avoid carrying buckets through boisterous calves.Being perfectly round, you can feed 20 calves right through to weaning, either inside or out.Fitted with Milk Bar™ Teats to improve average daily gains.

The solid base keeps the Milk Bar™ stable while 20 calves easily find a teat on the round design.

The Milk Bar™ 20 design makes it very sturdy for calves of all ages.

The feeder bowl stacks inside the base when not in use to reduce storage space.

There are loads of creative ways to fill the Milk Bar™ 20, but typically a hose is the easiest to avoid carrying buckets through boisterous calves.

Being perfectly round, you can feed 20 calves right through to weaning, either inside or out.

Fitted with Milk Bar™ Teats to improve average daily gains.

The Milk Bar™ 20 comes with the feeder bowl stacked inside the base and a pack of the bolts and instructions you will need to assemble the feeder ready for use.

  1. Place the feeder bowl upside down on the ground.

  2. Place the base on to the feeder bowl, lining up the bolt holes.

  3. Screw the bolts into place. They are wingnut so no need for any tools.

  4. Fill with milk and leave them to it.

When to Replace

Milk Bar™ Teats control the flow for around 120 feeds. This figure is influenced by cleaning regimes, as the natural rubber gradually absorbs milk fat and protein. With use, the teat softens and the flow increases - calf behaviour will indicate when the teats have become soft and need replacement! As the milk flow increases they will start to suck on each other or their surroundings (cross-suckling). As soon as you start to see cross-suckling, change your teats to prevent the next stage of fast flow - diarrhoea.

However - managing the teats as you would your milking liners helps maintain a consistent, controlled flow and takes away guess work.

A simple calculation will tell you when to replace the teats: 120 ÷ feeds per day ÷ 7 = weeks until replacement.

For example, if the teat is used twice a day, replace it every 8.5 weeks: 120 ÷ 2 ÷ 7 = 8.5 weeks.

If the teat is used four times a day, replace it every 4.2 weeks: 120 ÷ 4 ÷ 7 = 4.2 weeks.

Replace immediately if calves start gulping or cross-suckling.Good teat management helps maintain good calf digestive health.

How to Change

Milk Bar™ Teats use a hygienic pull-through design that fits tightly against the feeder wall to minimise milk build-up.

Correct installation is important: position the slit vertically for optimum performance.

  1. Teat Tool: The quickest and easiest removal method.

  2. By hand: Pull the teat straight up or down—not directly outward.

  3. Cutting: Use a sharp blade away from your body.

Check the new teat is inserted with the slit vertical.

Milk contains both fat and protein, which can form biofilm. This biofilm can give bacteria a perfect enviroment to multiply, even when a surface looks clean. Effective cleaning must remove both fat and protein.

Rinse equipment soon after feeding so milk does not dry onto the surface.

Use warm water and a suitable detergent rather than very hot water. Hot water can set or bake milk protein onto the equipment.

Milk Bar™ Teats are made from high-quality natural rubber, so they should be cleaned with a non-chlorine detergent. Chlorine-based detergents damage natural rubber, reducing teat life and performance.

Clean thoroughly at least twice a week, and rinse after every feed. Regular cleaning removes milk fat and protein before they form biofilms that allow bacteria to grow, helping maintain excellent hygiene for every feed.

  1. Rinse with water.

  2. Apply a gentle, non-chlorine detergent as directed.

  3. Lightly brush the outside while bending each teat so detergent reaches the inner wall.

  4. Rinse thoroughly.

The Milk Bar™ 20 comes with Milk Bar™ Teats fitted

Volume: 120L

Weight: 12.5kg

Diameter: 900mm

Height: 900mm

Warranty

The feeder has a two year warranty with proof of purchase.

The warranty does not apply to consumable parts (teats).

Made from food grade polyethylene and U.V Stabilised for long life.

Lorem ipsum dolor sit amet consectetur

Related products