Milk Bar
900112.jpg

Milk Bar™ Teat 50 Pack

Product No. 900112

A 50-pack of Milk Bar™ Teats for farms that need a practical supply of replacement teats on hand.

A 50-pack of Milk Bar™ Teats for farms that need a practical supply of replacement teats on hand.

It is important for calf health that milk is delivered at the right speed to optimise digestive health and performance.

Managing teats and feeders helps to streamline the calf operation and prevent the problems caused by fast feeding.

Groups from Day 1: Start the season or new batch of calves with new Milk Bar™ Teats in your feeders. This minimises the disruption from a mid-season teat change and gives calves the perfect flow from start to finish. Use one feeder per pen to reduce time and extend teat life.

Individual to Groups: Start each new calf with a new Milk Bar™ Teat and keep this teat with this calf until weaning - Follow the simple rule of One Calf - One Teat for best results!

  1. Use the Milk Bar™ Training Teat for the first few days - until the calf is drinking confidently.

  2. Place a new Milk Bar™ Teat into the single feeder - this feeder stays with this calf. Use one feeder per pen/ hutch to reduce time and improve teat management.

  3. When calves are ready to move into a group, remove the Milk Bar™ Teat from the single feeder and place into the group feeder. This feeder stays with these calves until weaning.

Pairs to Groups: As in the Individual to Groups system - feeder management is key.

  1. Use the Milk Bar™ Training Teat for the first few days - until the calves are drinking confidently.

  2. Place new Milk Bar™ Teats into the pair feeder - this feeder stays with these calves. Use one feeder per pen/ hutch to reduce time and improve teat management.

  3. When calves are ready to move into a bigger group, remove the Milk Bar™ Teat from the pair feeder and place into the group feeder. This feeder stays with these calves until weaning.

Milk Bar™ Teats use a hygienic pull-through design that fits tightly against the feeder wall to minimise milk build-up.

Correct installation is important: position the slit vertically for optimum performance.

  • Teat Tool: The quickest and easiest removal method.

  • By hand: Pull the teat straight up or down—not directly outward.

  • Cutting: Use a sharp blade away from your body. Fit the replacement with the slit vertical.

When to Replace

Milk Bar™ Teats control the flow for around 120 feeds. This figure is influenced by cleaning regimes, as the natural rubber gradually absorbs milk fat and protein. With use, the teat softens and the flow increases.

Managing the teats as you would your milking liners helps maintain a consistent, controlled flow.

A simple calculation will tell you when to replace the teats: 120 ÷ feeds per day ÷ 7 = weeks until replacement.

For example, if the teat is used twice a day, replace it every 8.5 weeks: 120 ÷ 2 ÷ 7 = 8.5 weeks.

If the teat is used four times a day, replace it every 4.2 weeks: 120 ÷ 4 ÷ 7 = 4.2 weeks.

Replace immediately if calves start gulping or cross-suckling. Regular inspection helps maintain good calf digestive health.

Milk contains both fat and protein, which can form biofilm. This biofilm can give bacteria a perfect enviroment to multiply, even when a surface looks clean. Effective cleaning must remove both fat and protein.

Rinse equipment soon after feeding so milk does not dry onto the surface.

Use warm water and a suitable detergent rather than very hot water. Hot water can set or bake milk protein onto the equipment.

Milk Bar™ Teats are made from high-quality natural rubber, so they should be cleaned with a non-chlorine detergent. Chlorine-based detergents damage natural rubber, reducing teat life and performance.

Clean thoroughly at least twice a week, and rinse after every feed. Regular cleaning removes milk fat and protein before they form biofilms that allow bacteria to grow, helping maintain excellent hygiene for every feed.

  1. Rinse with water.

  2. Apply a gentle, non-chlorine detergent as directed.

  3. Lightly brush the outside while bending each teat so detergent reaches the inner wall.

  4. Rinse thoroughly.

Pack Size: 50

Milk Bar™ Teats come in recyclable packaging.

Milk Bar™ Teats are made from a the highest grade natural rubber.

Milk Bar™ Teats are protected by patents and registered designs, reflecting decades of innovation dedicated to improving calf health and feeding performance.

NZ Pat Appln 727000, 787055. NZ Des Reg. 420972 PCT Patent Applications PCT/NZ2016/050190 & PCT/NZ2020/050110 International Patents and Designs pending or apply.

Lorem ipsum dolor sit amet consectetur

Related products