Milk Bar™ ULTRA 1 4L (INJ)
Product No. 910960
Infused with antimicrobial silver and fitted with an easy-change teat system. The new Milk Bar™ Ultra Range is carefully manufactured with FDA and food contact approved, antimicrobial materials. The silver compounds inhibit the growth of MRSA (Methicillin-Resistant Staphylococcus Aureus), S.Aureus and E.Coli by up to 99.9%. This feeder provides another layer of protection for young calves.The feeder holds 4L and features a self locking catch and sits on 25mm rails.
Infused with antimicrobial silver and fitted with an easy-change teat system.
The new Milk Bar™ Ultra Range is carefully manufactured with FDA and food contact approved, antimicrobial materials. The silver compounds inhibit the growth of MRSA (Methicillin-Resistant Staphylococcus Aureus), S.Aureus and E.Coli by up to 99.9%. This feeder provides another layer of protection for young calves.
The feeder holds 4L and features a self locking catch and sits on 25mm rails.
Hang the Milk Bar™ Ultra 1 4L on rails or pipes up to 25mm wide. Don’t force the feeder onto a wider rail as it can result in cracking the base of the hook.
Rail Height
To give your calves the best drinking position, hang the Milk Bar™ Ultra 1 4L on a rail around 85cm high. This puts the teat at 65cm which is the optimum height for calves and helps the oesophageal groove to close.
The Milk Bar™ 1 can be fitted with a Milk Bar™ Training Teat or a Milk Bar™ Teat.
When to Replace
Milk Bar™ Teats control the flow for around 120 feeds. This figure is influenced by cleaning regimes, as the natural rubber gradually absorbs milk fat and protein. With use, the teat softens and the flow increases - calf behaviour will indicate when the teats have become soft and need replacement! As the milk flow increases they will start to suck on each other or their surroundings (cross-suckling). As soon as you start to see cross-suckling, change your teats to prevent the next stage of fast flow - diarrhoea.
However - managing the teats as you would your milking liners helps maintain a consistent, controlled flow and takes away guess work.
A simple calculation will tell you when to replace the teats: 120 ÷ feeds per day ÷ 7 = weeks until replacement.
For example, if the teat is used twice a day, replace it every 8.5 weeks: 120 ÷ 2 ÷ 7 = 8.5 weeks.
If the teat is used four times a day, replace it every 4.2 weeks: 120 ÷ 4 ÷ 7 = 4.2 weeks.
Replace immediately if calves start gulping or cross-suckling.Good teat management helps maintain good calf digestive health.
How to Change
Milk Bar™ Teats use a hygienic pull-through design that fits tightly against the feeder wall to minimise milk build-up.
Correct installation is important: position the slit vertically for optimum performance.
Teat Tool: The quickest and easiest removal method.
By hand: Pull the teat straight up or down—not directly outward.
Cutting: Use a sharp blade away from your body.
Check the new teat is inserted with the slit vertical.
Milk contains both fat and protein, which can form biofilm. This biofilm can give bacteria a perfect enviroment to multiply, even when a surface looks clean. Effective cleaning must remove both fat and protein.
Rinse equipment soon after feeding so milk does not dry onto the surface.
Use warm water and a suitable detergent rather than very hot water. Hot water can set or bake milk protein onto the equipment.
Milk Bar™ Teats are made from high-quality natural rubber, so they should be cleaned with a non-chlorine detergent. Chlorine-based detergents damage natural rubber, reducing teat life and performance.
Clean thoroughly at least twice a week, and rinse after every feed. Regular cleaning removes milk fat and protein before they form biofilms that allow bacteria to grow, helping maintain excellent hygiene for every feed.
Rinse with water.
Apply a gentle, non-chlorine detergent as directed.
Lightly brush the outside while bending each teat so detergent reaches the inner wall.
Rinse thoroughly.
The Milk Bar™ Ultra 1 4L comes ready to use with a Milk Bar™ Teat and self locking catch.
Volume: 4L
Weight: 700gms
Length: 210mm
Height: 210mm
Width: 210mm
Replacment Milk Bar™ Black Self Latching Hook available Code: 950208
Replacement Milk Bar™ 1 4L Teat Attachment Kit Code: 900110
Warranty
The feeder has a two year warranty with proof of purchase.
The warranty does not apply to consumable parts (teats and hooks).
Made from food grade polyethylene and U.V Stabilised for long life.