Milk Bar™ ULTRA XL8
Product No. 910957
A wider teat spacing for larger calves, the Ultra XL8 is infused with antimicrobial silver to inhibit the growth of common pathogens. Carefully manufactured with FDA and food contact approved, antimicrobial materials - the silver compounds inhibit the growth of MRSA (Methicillin-Resistant Staphylococcus Aureus), S.Aureus and E.Coli by up to 99.9%. The Milk Bar™ Ultra XL8 has a wide teat spacing for larger calves.The Ezi Lock Hooks are fitted to the outside of the feeder and can be mounted on height adjustment plates.
A wider teat spacing for larger calves, the Ultra XL8 is infused with antimicrobial silver to inhibit the growth of common pathogens.
Carefully manufactured with FDA and food contact approved, antimicrobial materials - the silver compounds inhibit the growth of MRSA (Methicillin-Resistant Staphylococcus Aureus), S.Aureus and E.Coli by up to 99.9%.
The Milk Bar™ Ultra XL8 has a wide teat spacing for larger calves.
The Ezi Lock Hooks are fitted to the outside of the feeder and can be mounted on height adjustment plates.
With Ezi Lock Hooks you can hang this feeder on anything from wooden rails to hutch gates.
Hang the feeder in place, lock the hooks and fill with milk.
After feeding you can either remove the feeder, or flip it upside down until the next feed.
Rail Height
To give your calves the best drinking position, hang the feeder on a rail around 100cm high. This puts the teat at 65cm which is the optimum height for calves and helps the oesophageal groove to close and milk to bypass the rumen.
If your rails are higher than 1m, then simply attach the Ultra Height Plates to the feeder to get the optimum height for calves.
When to Replace
Milk Bar™ Teats control the flow for around 120 feeds. This figure is influenced by cleaning regimes, as the natural rubber gradually absorbs milk fat and protein. With use, the teat softens and the flow increases - calf behaviour will indicate when the teats have become soft and need replacement! As the milk flow increases they will start to suck on each other or their surroundings (cross-suckling). As soon as you start to see cross-suckling, change your teats to prevent the next stage of fast flow - diarrhoea.
However - managing the teats as you would your milking liners helps maintain a consistent, controlled flow and takes away guess work.
A simple calculation will tell you when to replace the teats: 120 ÷ feeds per day ÷ 7 = weeks until replacement.
For example, if the teat is used twice a day, replace it every 8.5 weeks: 120 ÷ 2 ÷ 7 = 8.5 weeks.
If the teat is used four times a day, replace it every 4.2 weeks: 120 ÷ 4 ÷ 7 = 4.2 weeks.
Replace immediately if calves start gulping or cross-suckling.Good teat management helps maintain good calf digestive health.
How to Change
Milk Bar™ Teats use a hygienic pull-through design that fits tightly against the feeder wall to minimise milk build-up.
Correct installation is important: position the slit vertically for optimum performance.
Teat Tool: The quickest and easiest removal method.
By hand: Pull the teat straight up or down—not directly outward.
Cutting: Use a sharp blade away from your body.
Check the new teat is inserted with the slit vertical.
Milk contains both fat and protein, which can form biofilm. This biofilm can give bacteria a perfect enviroment to multiply, even when a surface looks clean. Effective cleaning must remove both fat and protein.
Rinse equipment soon after feeding so milk does not dry onto the surface.
Use warm water and a suitable detergent rather than very hot water. Hot water can set or bake milk protein onto the equipment.
Milk Bar™ Teats are made from high-quality natural rubber, so they should be cleaned with a non-chlorine detergent. Chlorine-based detergents damage natural rubber, reducing teat life and performance.
Clean thoroughly at least twice a week, and rinse after every feed. Regular cleaning removes milk fat and protein before they form biofilms that allow bacteria to grow, helping maintain excellent hygiene for every feed.
Rinse with water.
Apply a gentle, non-chlorine detergent as directed.
Lightly brush the outside while bending each teat so detergent reaches the inner wall.
Rinse thoroughly.
The Milk Bar™ Ultra XL8 comes ready to use with Milk Bar™ Teats and hooks fitted.
Volume: 60L
Weight: 5kg
Length: 850mm
Height: 430mm
Width: 460mm
Warranty
The feeder has a two year warranty with proof of purchase.
The warranty does not apply to consumable parts (teats and hooks).
Made from food grade polyethylene and U.V Stabilised for long life.